|
主要论文
|
Chengyong Wang, Feng Ding, Dewen Tang, Lijuan Zheng, Suyang Li, Yingxing Xie；Modeling and simulation of the high-speed milling of hardened steel SKD11 (62 HRC) based on SHPB technology；International Journal of Machine Tools and Manufacture；Volume 108, September 2016, Pages 13–26. Suyang Li, Chengyong Wang, , Lijuan Zheng, Yujia Wang, Xinpei Xu, Feng Ding；Dynamic stability of cemented carbide circular saw blades for woodcutting；Journal of Materials Processing Technology；Volume 238, December 2016, Pages 108–123. ShixiongWu, ZhenyuZhao, ChengYongWang, YingxingXie, WeiMa；Optimization of toolpath with circular cycle transition for sharp corners in pocket milling；The International Journal of Advanced Manufacturing Technology；February 2016；DOI: 10.1007/s00170-016-8364-3. Shan Li,Li Juan Zheng,Cheng Yong Wang,Lianyu Fu;Micro drilling quality of the Cu/BT laminate for IC substrate；Circuit World 42(2):55-62,May 2016. R. J. Wang, C. Y. Wang, W. Wen, J. Wang；Experimental study on a micro-abrasive slurry jet for glass polishing；The International Journal of Advanced Manufacturing Technology；July 2016； doi:10.1007/s00170-016-9109-z. Wu Shixiong, , Ma Wei, Li Bin, Wang Chengyong;Trochoidal machining for the high-speed milling of pockets;Journal of Materials Processing Technology, 2016, 233:29-43. Wang C Y, Xie Y X, Qin Z, et al. Wear and breakage of TiAlN- and TiSiN-coated carbide tools during high-speed milling of hardened steel[J]. Wear, 2015, s 336–337:29-42. Lin H, Wang C, Yuan Y, et al. Tool wear in Ti-6Al-4V alloy turning under oils on water cooling comparing with cryogenic air mixed with minimal quantity lubrication. International Journal of Advanced Manufacturing Technology, 2015, 81(1):1-15. Zheng L, Wang C, Zhang X, et al. The entry drilling process of flexible printed circuit board and its influence on hole quality[J]. Circuit World, 2015, 41(4):147-153. Wang C, Xie Y, Zheng L, et al. Research on the Chip Formation Mechanism during the high-speed milling of hardened steel[J]. International Journal of Machine Tools & Manufacture, 2014, 79(4):31-48. Zheng L J, Wang C Y, Qu Y P, et al. Interaction of cemented carbide micro-drills and printed circuit boards during micro-drilling. International Journal of Advanced Manufacturing Technology, 2014, 77(5-8):1305-1314. Linlin X U, Wang C, Jiang M, et al. Drilling Force and Temperature of Bone under Dry and Physiological Drilling Conditions[J]. Chinese Journal of Mechanical Engineering, 2014, 27(6):1240-1248. J.B. Mao, F.L. Zhang, , G.C. Liao, Y.M. Zhou, H.P. Huang, C.Y. Wang, S.H. Wu;Mao J B, Zhang F L, Liao G C, et al. Effect of granulated sugar as pore former on the microstructure and mechanical properties of the vitrified bond cubic boron nitride grinding wheels[J]. Materials & Design, 2014, 60(8):328-333. Wang L, Zheng L, Wang C Y, et al. Experimental study on micro-drills wear during high speed of drilling IC substrate[J]. Circuit World, 2014, 40(2):61-70(10). Zheng L, Wang C, Yang L, et al. Characteristics of chip formation in the micro-drilling of multi-material sheets. International Journal of Machine Tools & Manufacture, 2012, 52(1):40–49. Zheng L J, Wang C Y, Fu L Y, et al. Wear mechanisms of micro-drills during dry high speed drilling of PCB[J]. Journal of Materials Processing Technology, 2012, 212(10):1989-1997. Zhou H, Wang C, Deng J, et al. Radial Grip Rigidity of the Matching of Lengthened Shrink-fit Holder and Cutter in High-speed Milling. Chinese Journal of Mechanical Engineering, 2012, 25(1):179-183. Zhou H, Wang C, Peng D T R. Dynamic analysis of the lengthened shrink-fit holder and cutting tool system in high-speed milling[J]. Machining Science & Technology, 2012, 16(2):157-172. Zhang F L, Yang Z F, Zhou Y M, Wang C Y, et al. Fabrication of grinding tool material by the SHS of Ni–Al/diamond/dilute[J]. International Journal of Refractory Metals & Hard Materials, 2011, 29(3):344-350. Fan J M, Li H Z, Wang J, CY Wang, et al. A study of the flow characteristics in micro-abrasive jets. Experimental Thermal & Fluid Science, 2011, 35(6):1097-1106. Zhou Y M, Zhang F L, Wang C Y. Effect of Ni–Al SHS reaction on diamond grit for fabrication of diamond tool material. International Journal of Refractory Metals & Hard Materials, 2010, 28(3):416-423. Runping Shi; Chengyong Wang;Review on advanced composite materials boring mechanism and tools;Proc SPIE, 2010, 7997(13):1216-1217. L. Zhou, C. Y. Wang, Z. Qin. Investigation of Chip Formation Characteristics in Orthogonal Cutting of Graphite[J]. Materials & Manufacturing Processes, 2009, 24(12):1365-1372. D. W. Tang,C. Y. Wang,Y. N. Hu,Y. X. Song;Constitutive equation for hardened SKD11 steel at high temperature and high strain rate using the SHPB technique;Proc. SPIE 7522,article id. 75226B, 12 pp. (2009); doi: 10.1117/12.851262. Wang C Y, Zhou Y M, Zhang F L, et al. Interfacial microstructure and performance of brazed diamond grits with Ni–Cr–P alloy. Journal of Alloys & Compounds, 2009, 476(1):884-888. Yu D, Wang C, Cheng X, et al. Microstructure and properties of TiAlSiN coatings prepared by hybrid PVD technology. Thin Solid Films, 2009, 517(17):4950–4955. Zhou L, Wang C.Y. and Qin Z. Tool Wear characteristics in high speed milling of graphite using micro coated carbide endmill. Proceedings of the Institution of Mechanical Engineers, Part B. Journal of Engineering Manufacture, 2009, 223(2): 267-277. Tang D W, Wang C Y, Hu Y N, et al. Finite-Element Simulation of Conventional and High-Speed Peripheral Milling of Hardened Mold Steel. Metallurgical & Materials Transactions A, 2009, 40(13):3245-3257. Yu D, Wang C, Cheng X, et al. Optimization of hybrid PVD process of TiAlN coatings by Taguchi method. Applied Surface Science, 2008, 255(5):1865-1869. Zhang F L, Zhu M, Wang C Y. Parameters optimization in the planetary ball milling of nanostructured tungsten carbide/cobalt powder[J]. International Journal of Refractory Metals & Hard Materials, 2008, 26(4):329-333. Zhou H, Wang C, Zhao Z. Dynamic characteristics of conjunction of lengthened shrink-fit holder and cutting tool in high-speed milling. Journal of Materials Processing Technology, 2008, 207(s 1–3):154-162. Yumei Zhou, Chengyong Wang, Fenglin Zhang, et al. Cr Powder-Activated Induction Brazing of Diamond Grits with Ag–Cu–Zn Alloy. Materials & Manufacturing Processes, 2008, 23(4):352-356. Zhao Z Y, Wang C Y, Zhou H M, et al. Pocketing toolpath optimization for sharp corners. Journal of Materials Processing Technology, 2007, 192:175-180. Wang Chengyong, Zhou Li, Fu Hao, Hu Zhouling. High speed milling of graphite electrode with endmill of small diameter. Chinese Journal of Mechanical Engineering, 2007, 20(4):27-31. Zhang F L, Wang C Y, Chen Z N G J. Effect of Electrical Spark Discharging Parameters on the Etching of Chemical Vapor Deposition (CVD) Diamond Film. Materials & Manufacturing Processes, 2007, 22(22):859-864. Wang C Y, Zhang F L, Kuang T C, et al. Chemical/mechanical polishing of diamond films assisted by molten mixture of LiNO3 and KNO3. Thin Solid Films, 2006, 496(2):698–702. C. Y. Wang, X. Wei, H. Yuan. Polishing of ceramic tiles. Materials & Manufacturing Processes, 2006, 17(3):401-413. Zhang F L, Wang C Y, Zhu M. Nanostructured WC/Co composite powder prepared by high energy ball milling. Scripta Materialia, 2003, 49(11):1123-1128. Wang C. How abrasive machining affects surface characteristics of vitreous ceramic tile. American Ceramic Society Bulletin, 2003:9201-9208. Wei X, Wang C Y, Zhou Z H. Study on the fuzzy ranking of granite sawability. Journal of Materials Processing Technology, 2003, 139(139):277-280. Wang C Y, Clausen R. Computer simulation of stone frame sawing process using diamond blades. International Journal of Machine Tools & Manufacture, 2003, 43(6):559-572. Wang C Y, Clausen R. Marble cutting with single point cutting tool and diamond segments. International Journal of Machine Tools & Manufacture, 2002, 42(42):1045-1054. |
